Re: How to pass over the 80 Character Barrier for String Parameters
A possible work around would be to use two parameters and put most of your text in one and the remaining in the next. Not pretty, but since there is a limit, I don't see another work around. At least...
View ArticleClik here to view.
Creo Parametric problem with start up
Hi Community,Excuse me for my bad english and my unknowledge about Creo, I am a newbie I am a Student wich has to work with that software at home.After install i have a problem now during starting the...
View ArticleClik here to view.
Re: How to pass over the 80 Character Barrier for String Parameters
Hello Chantal Gagne here is another way (sorry for my english)1. Create Note_12. Type text to the new note like this3. Create PARAMETER_1 and choose type "note" and value "note_1 id" (see in the...
View ArticleRe: How to pass over the 80 Character Barrier for String Parameters
It's good to see that FORTRAN/Hollerith punch card conventions are alive and well. It's probably baked into Windchill as well to only accept 80 character parameter strings.
View ArticleRe: How to pass over the 80 Character Barrier for String Parameters
I have the same issue where I can set the attribute size to be anything in PDMLink, but am crippled by CREO to 80 characters. I contacted PTC TS a couple weeks back and they were unable to provide a...
View Articleregenerating the tubing in EFX extension
i am trying to regenerate the tubing in EFX extension and simulate it but its not happening can someone tell me the reason behind it.
View ArticleRe: Unable to open Protoolkit help file.
Hi Sandeep, This issue may occur due to Changes to JRE Security Dialogs. For detailed information refer below articles....
View ArticleHow to export DXF of an assembly
I have an assembly that represents a rigid/flex board. Each board is a solid shape and the flexes connecting them are done with sheetmetal. I want to export the flattened model as a DXF so I can...
View ArticleRe: How to export DXF of an assembly
If you take the file into AutoCAD, or draftsight (free version of AutoCAD), you can delete the lines then save in the configuration you desire.
View ArticleRe: How to export DXF of an assembly
I would very much like to skip bringing it into yet another tool.
View ArticleRe: How to export DXF of an assembly
you can also make sure the following config is set to no: smt_outside_mold_linesyes, no* yes—Outside mold lines are created during the flat pattern creation. no—Outside mold lines are not...
View ArticleRe: How to export DXF of an assembly
Re-import them into a new Pro/E drawing and delete the lines there, then export that.Remember to turn off the format to avoid adding the outline to the DXF file.
View ArticleClik here to view.
animation help - this look shocking
Hi All I have been working on a project over the last couple of weeks preparing model and drawings for a Capex proposal for new plant. now I have been doing some animation of the equipement in action....
View ArticleRe: animation help - this look shocking
I think PhotoRender is crippled to help sell PhotoLux. I don't use it. You need the larger frame and I like using shaded with reflections; turning the options for higher quality graphics; removng the...
View ArticleRe: Multiple flange
Hi Stefan, Flange can be created using a single edge or chain of edges only. For different edges you need to create multiple flanges. Regards,Mahesh
View ArticleRe: Insert image to drawing?
Thanks guys, I was able to get the image in from paint. Now the issue I have is that I lose the detail from the image. I kind of expected this, so I'm going to go a different route. Thanks for the...
View ArticleRe: Multiple flange
Hi Stefan, For flange creation, only available choice is to create multiple flanges, however your second target about controlling the angle can hit by relations. Using relations you can control the...
View ArticleRe: animation help - this look shocking
Right, that was the comment below the image. It is a catch 22 where it is easy to have a mechanism cycle one full cycle stopping where it started, but when you make a looping movie, you can always...
View ArticleRe: the best way to assemble in CREO2
Correct link: 3D dragger in assembly - allow a defualt to be set in the Config.pro
View ArticleRe: Insert image to drawing?
You can set the resolution for images in drawings also. By default it is only 150 DPI. See this post: How to insert a PDF in detail To get a good .BMP image I scale the source up to look good on the...
View Article